Upload issue



  • Hello, I'm having issue uploading code to codrone remote. Attached video

         Using Port                    : COM3
         Using Programmer              : arduino
         Overriding Baud Rate          : 115200
         AVR Part                      : ATmega32
         Chip Erase delay              : 9000 us
         PAGEL                         : PD7
         BS2                           : PA0
         RESET disposition             : dedicated
         RETRY pulse                   : SCK
         serial program mode           : yes
         parallel program mode         : yes
         Timeout                       : 200
         StabDelay                     : 100
         CmdexeDelay                   : 25
         SyncLoops                     : 32
         ByteDelay                     : 0
         PollIndex                     : 3
         PollValue                     : 0x53
         Memory Detail                 :
    
                                  Block Poll               Page                       Polled
           Memory Type Mode Delay Size  Indx Paged  Size   Size #Pages MinW  MaxW   ReadBack
           ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
           eeprom         4    10    64    0 no       1024    4      0  9000  9000 0xff 0xff
           flash         33     6    64    0 yes     32768  128    256  4500  4500 0xff 0xff
           lfuse          0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
           hfuse          0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
           lock           0     0     0    0 no          1    0      0  2000  2000 0x00 0x00
           signature      0     0     0    0 no          3    0      0     0     0 0x00 0x00
           calibration    0     0     0    0 no          4    0      0     0     0 0x00 0x00
    
         Programmer Type : Arduino
         Description     : Arduino
    

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x0a

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x55

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x11

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x02
    Hardware Version: 4744608
    Firmware Version: 0.4611299

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0xe0

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x02

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x83

    avrdude: stk500_getparm(): (a) protocol error, expect=0x14, resp=0x33
    avrdude: stk500_recv(): programmer is not responding
    Vtarget : 420030.5 V
    Varef : 197625606.4 V
    Oscillator : 0.531 Hz
    SCK period : 11269644.1 us

    avrdude: stk500_recv(): programmer is not responding
    avrdude: stk500_recv(): programmer is not responding
    avrdude: stk500_recv(): programmer is not responding
    avrdude: initialization failed, rc=-1
    Double check connections and try again, or use -F to override
    this check.

    the selected serial port
    does not exist or your board is not connected
    avrdude: stk500_recv(): programmer is not responding

    avrdude done.

    Thank you.

    Please help on this.

    Thanks in advance
    Nivedh


  • administrators

    @nporeddy ,
    Do you want to code in Python or in Arduino? Uploading to the CoDrone remote requires the CP210x driver and Arduino installed. For Python, you only need the Bluetooth board. Let me know what platform you are trying to use, as well as any screenshots of the code you are trying to upload. Thanks!


Log in to reply
 

Looks like your connection to Robolink community was lost, please wait while we try to reconnect.